充氣螺旋閘門是我公司根據氣力輸送工況需求研制的一種調節、切斷型閘門，廣泛適用于建材、冶金、礦山、輕工、玻璃等行業的氣力輸送系統。
This valve is the new designed product for adjusting and cutting off on the base of working condition of gas power transportation, which is widely used in the gas power transportation system in building material, glass, mining, light industry and metallurgy industries etc.
結構特點：
Structure characteristic:
充氣螺旋閘門采用優質碳鋼焊接而成，分上下兩個通道，下通道為充氣層，上通道為輸送物料層，中間為透氣層。螺旋型閘板可任意調節閘門開度，特別適用于無粘度的干燥粉料，細微顆粒料等。具有能耗小，無噪音，無污染，少維修，無卡阻，操作方便，使用壽命長等特點。
The valve is welded in fine carbon steel. The lower tunnel of valve is used to aerate, the upper tunnel is used to transport material and the middle layer is breather layer. The gate position can be adjusted by screw slide plate. The valve is suitable for no viscosity powder and small grain etc. it has the features of little energy consumption, no noise, no pollution, little maintenance, no obstruction, convenient operation, long service life etc.
性能參數：
Performance parameter:
充氣壓力 Aeration pressure | 耗氣量 Gas rate | 含水量 Water content | 適用介質 Suitable medium |
0.005～0.01MPa | ≈ 0.13～0.26 m 3 /min | ＜ 1﹪ | 水泥生料、水泥成品、、鋁土等 Cement raw, finish cement, talcum powder, alumina etc |
工作原理：
Working principle
物料調節閘門由風機給予低壓小容量空氣經下通道入氣口由充氣層充氣 ， 氣體透過沸騰板均勻向上噴吹 ， 鼓動物料向上位移 ， 物料自重下落時由設備安裝斜度而產生位移 ， 不斷重復致使物料向前位移 。 調節閘門由絲桿閘板及密封副等組成，由人工轉動手輪帶動絲桿旋轉，使閘門隨著螺旋絲桿產生位移，起到任意調節或切斷的作用。
The low pressure little volume air supplied by wind machine is aerated from inflation layer through lower tunnel intake. Then the gas blows upwards through boiling plate to drive the material move upwards. Because of the installation incline, material will fall in the effect of gravity. The unceasing repeating actions make the material move forwards. The valve is made up of slide plate and sealing pairs etc. rotate the hａnd wheel and the screw pole will rotate in the same time to drive the gate move, which has the function of adjusting or cutting off the valve freely.
使用說明
Usage explanation
• 安裝前請檢查閘門內腔有無雜物附著，沸騰板受潮沒有，如沸騰板受潮請更換后再進行安裝，否則影響使用效果。檢查各傳動部分是否靈活可靠。法蘭間連接需加裝密封墊片后再均勻擰緊螺栓。
• 調試時，人工轉動手輪，順時針旋轉為關，反之為開，運行無卡阻現象即可。
• Check the valve if there is lumber inside the body or the boiling disc is damp. Exchange the boiling disc before install if it is damp. Otherwise it will affect the operation. Check the transmission part. Add sealed shim between the two flanges and then lock down the bolt equably.
• Rotate the hａnd wheel by hａnd when debug the valve. Clockwise rotate of valve denotes closing, otherwise denotes opening. It will be all right if there is no obstruction.
I 型外形圖 II 型 外形圖 ：
Appearancefigure: Appearance figure:
外形連接尺寸 ：
Appearance joint dimensions:
規格 Size | 200 | 250 | 300 | 350 | 400 | 450 | 500 | 550 | 600 | 650 |
A | 200 | 250 | 300 | 350 | 400 | 450 | 500 | 550 | 600 | 650 |
A1 | 340 | 390 | 440 | 490 | 540 | 600 | 640 | 690 | 740 | 790 |
B | 250 | 300 | 350 | 400 | 450 | 500 | 552 | 600 | 650 | 700 |
B1 | 390 | 440 | 490 | 540 | 585 | 635 | 693 | 743 | 795 | 845 |
C | 290 | 340 | 390 | 440 | 490 | 540 | 600 | 650 | 700 | 750 |
C1 | 430 | 480 | 530 | 580 | 630 | 690 | 740 | 790 | 840 | 890 |
X | 3 | 3 | 4 | 4 | 5 | 5 | 6 | 6 | 7 | 7 |
Y | 6 | 6 | 7 | 7 | 8 | 8 | 9 | 9 | 10 | 10 |
n-d | 18- Φ 10 | 18- Φ 10 | 22- Φ 10 | 22- Φ 10 | 26- Φ 14 | 26- Φ 14 | 30- Φ 14 | 30- Φ 14 | 34- Φ 14 | 34- Φ 14 |
L | 300 | 300 | 300 | 300 | 300 | 400 | 400 | 400 | 400 | 400 |
B | 8 | 8 | 8 | 8 | 10 | 10 | 10 | 10 | 12 | 12 |
N | 40 | 40 | 40 | 40 | 40 | 40 | 45 | 45 | 45 | 45 |
M | G1/2” | G1/2” | G1/2” | G1/2” | G1/2” | G1” | G1” | G1” | G1” | G1” |
H | 900 | 1000 | 1100 | 1200 | 1300 | 1400 | 1500 | 1600 | 1700 | 1800 |
S | 265 | 315 | 365 | 415 | 465 | 565 |
訂貨須知 :
Information for order
• 選用訂貨時請參照產品樣本注明產品規格、型號及技術參數（使用溫度、設備工況、介質性質等）。
• 表格中未列規格、用于特殊介質或其它特殊要求，請與我公司經銷部、技術部聯系，可為您另行設計、制造。
• Please indicate the type, model and technical parameter (using temperature, working condition of equipment, characteristic of medium and product material etc) referring to the product sample when you place an order.
• If you have other special demand, need special medium or the data that is not listed in the table, please contact with our department of market and technology. We can design and manufacture for you especially but you must indicate your special demａnd in the contract.
