德國奧萊斯OLES進口波紋管減壓閥

【進口波紋管減壓閥】結構說明：

1、閥前進口介質壓力從閥瓣和閥體密封圈開啟間隙進入體腔使介質壓力流滿波紋管的組合箱，波紋管和彈簧因受介質壓力的擠壓而壓縮，閥瓣隨著閥桿位移，閥瓣產生對閥體密封圈的關閉，將閥前介質截止，不作閥后介質壓力的補充。當閥后的介質壓力降低，波紋管因受調節彈簧的徑項力，使波紋管疊紋變形，閥桿將閥瓣頂開。使介質通過閥體密封圈補充閥后壓力的降低。 2、本閥是由閥體、閥蓋、閥瓣、閥體密封圈、閥桿、波紋管、調節彈簧等零件組成，體腔進口組裝有閥瓣、閥體密封圈和輔彈簧，輔彈簧是保持閥瓣和閥體密封圈自動的密封，出口體腔組裝彈性密封元件（波紋管）即保證閥后介質壓力的泄漏和克服壓力不均勻度的補償。螺釘是調整彈簧負荷壓力減壓閥工作性能。

1. The medium pressure at the valve front inlet enters the body cavity from the opening clearance between the disc and the body seal ring, so that the medium pressure flows into the combined box of the bellows. The bellows and springs are compressed by the pressure of the medium. With the displacement of the valve stem, the disc closes the body seal ring and cuts off the medium in front of the valve and does not act as the medium pressure behind the valve. Supplement. When the medium pressure behind the valve decreases, the bellows are deformed by the diameter force of the regulating spring, and the valve stem opens the disc. Make the medium through the valve body seal ring to supplement the pressure drop after the valve. 2. The valve is composed of valve body, cover, disc, body seal ring, stem, bellows, adjusting spring and other parts. The body cavity inlet is assembled with valve disc, body seal ring and auxiliary spring. The auxiliary spring is to keep the valve disc and body seal ring automatically sealed, and the outlet body cavity is assembled with elastic sealing elements (bellows) to ensure the rear of the valve. The leakage of medium pressure and the compensation of overcoming pressure nonuniformity. The screw is used to adjust the working performance of the spring load pressure relief valve.

【進口波紋管減壓閥】用途：

波紋管式減壓閥用于溫度在180℃以下的蒸汽、空氣及其無腐蝕性氣體的管路上，經過調節，使通過閥內的介質壓力減至某一需要的出口壓力，并使介質的出口壓力保持相對穩定，但波紋管減壓閥進口壓力與出口壓力之差必須大于或等于0.2MPa

【進口波紋管減壓閥】工作原理：

介質走向由上進下出，當調節出口壓力時，順時針旋轉調節螺栓，迫使活塞向下移動，打開主閥，改變節流面積，造成壓力損失，實現減壓。由于減壓閥閥后介質通過“X”通道流入活塞下腔并與活塞上方保持平衡，當壓力和流量變化時，使主閥節流面積始終保持相應位置，由于減壓閥Y42F采用卸荷機構，減小了進口壓力變化對出口壓力的影響，同時加大了出口壓力作用面積，即加大敏感元件作用面積，從而減小了閥門出口壓力偏差，大大提高了減壓閥的穩壓精度。

調壓方法：

1、關閉減壓閥前的截止閥，開啟減壓閥后的截止閥，制造下游低壓環境。

2、卸下減壓閥上端的防護罩調節螺釘按逆時針旋轉*位置（相對低出口壓力），然后關閉減壓閥后截止閥。

3、慢慢開啟減壓閥前的截止閥至全開。

4、順時針緩慢旋轉調節螺釘，將出口壓力調至所需的壓力（以閥后表為準）調整后，將鎖緊螺母?jìng)渚o，擰上防護罩，打開減壓閥后截止閥。